Support

I use a Shadow cloud PC, and I am trying to connect a TrackIR system to it. I have read through the forums to find out how to get it to work, and they all point me toward this service. I have installed the server on my local, the client on my Shadow and the VM software to connect it all. I can get the hub to pick up on the Shadow, but I keep getting this error,
"Error 2 installing drivers, the system cannot find the file specified."
The log for the client shows " INFO :No drivers found, they will be installed
2021-03-19 09:03:32 INFO :SetupDiEnumDeviceInterfaces failed

Hi,

I'm running VirtualHere client vhui64.exe v5.1.6 on a Windows Server 2016 Hyper-V VM, connecting to VirtualHere Server vhusbdwin64.exe, also v5.1.6, on a Windows Server 2016 Hyper-V host. I did not install Bonjour on the server, since this is a very straightforward permanent network connection and I didn't see any need for a discovery service.

Are there instructions for a complete newbie? I want to use a Raspberry Pi 0 w as the server at one location and a Linux desktop as client at another location. I think I got it installed on the Pi but I can't find newbie instructions to install the client on a Linux Mint desktop.

After connecting using EasyFind to my server, all the usb devices show up, but when I try connecting I get an error "Windows cannot find dpinsts.exe. Make sure you typed the name correctly, and then try again." after clicking ok, a message pops up "Error installing 2 drivers, the system cannot find the file specified"

Hello,

Is it possible to run the VirtualHere client on RedHat 8?

How can I install the required kernel modules?

Thank you,
Flavio

Hello,

I'm a Radio Amateur and would like to use a transceiver in my local network using a Raspberry 4 B and VH.

The transceiver is a Yaesu FT 991a (https://www.yaesu.com/indexVS.cfm?cmd=DisplayProducts&ProdCatID=102&enc…). Connected directly by USB it works fine.
Info: The transceiver has a built in sound card for Microphone / Speakers.

I'm trying to use a spacenavigator controller from my old 2010 mac (high sierra) laptop connected to a windows 7 server at office through Microsoft Remote desktop over OpenVPN.
I couldn't find any instruction on how to configure and forward ports for this kind of connections...
Sorry for the newbie question, but should I setup anything on the VPN before trying to correctly operate VirtualHere ?

Hi all,
I recently attempted to change the eth0 port on my Pi4 to a Static IP.. All works fine locally (Local LAN), but I can no longer see the Virtual Here server from a remote location.
Even though I have the correct port forwarding etc etc etc .

Anyone have any advice?
Cheers

Good morning,

Just wondered if anyone had come across a solution for what appears to be a server process crash on Raspberry Pi 3B+

Everything installed and running brilliantly - I'm using this to host a Steinberg USB dongle so I dont have to cart the device around to use Cubase 10.5 Pro. Its quick, easy and it works!

But I noticed that the server has stopped after a few hours . It's an easy fix to restart but it would be great to have to not do this if possible. Here's the process state after crash, and after restart:

Hello,

I am trying out VirtualHere after it was suggested on an Nvidia Shield forum.

I've installed the app to the Nvidia Shield TV and connected just one bluetooth dongle to the shield.

I am now running the client on Windows 10 Pro 64bit, but when I select to use the device I get the following errors.

2021-03-10 16:05:41 INFO :No drivers found, they will be installed
2021-03-10 16:05:46 INFO :SetupDiEnumDeviceInterfaces failed
2021-03-10 16:05:46 ERROR :Hub failed to open error, No more data is available. (0x00000103)