Support

I have tried both the 32 and 64 bit files of the free trial and both seem to crash right away. I found the following in the event log.

My creative live cam sync 1080p is connected to an android box but is not showing in the windows client. I have succesfully connected a wireless keyboard to the same Android box and I am seeing the message from Android VirtualHere server when I connect the webcam to force the openning of the app.

Please advise

Thank you in advance

<p>This software is amazing and it works like charm for android phones.
</p>
<p>It also looks like its working with Iphone (can be seen with lsusb, and vh says In-use by you), but libmobiledevice does not see Iphone attached.
</p>
<p>Seems like its issue with libusb, it can't set configuration (below), is that solveable? Would it work if client was mac instead linux?
</p>
<p>VirtualHere Host: MacMini 11.2.1, vh version: 4.2.5<br />
VirtualHere Client: Ubuntu (v18.04 and v20.04)

Hello Michael,

We have a setup with two UVC compliant cameras (512x640 rgb) (FLIR BOSON ir cameras) attached to the same Pi4. The cameras are read-out sequentially, VID0, VID1, VID0, VID1,,, Obviously we use the licensed version and it is started like this:
sudo ./vhusbdarmpi4
Both client (Win10/64b) and server are the latest from the website as of 2021-02-20

We see an erratic behavior in the way that
1) sometimes an image is black,
2) sometimes one image is replicated to the other cameras display - giving two identical displays.

I tried running virtualhere with a wii remote on a rpi3b+, and it seems to work fine. But once I connect more then one wii remote, I start getting really bad latency with the wii remotes. I tried running the virtualhere server on a seperate rpi4 without a gamestream running, it had the same bad latency. Is it possible to stream more then one wii remote? I also tried a local network steam link. The rpi's were on a remote network using the reverseclients option. The steam link also had the same latency issues

I'm having trouble getting my Xbox Wireless Adapter to enter "pairing" mode when plugged in to my nvidia Shield (2019 pro).

When I plug it in, it appears to be recognized by the server on the Shield and passed to the client on my windows 10 host.

It also recognizes the adapter and drivers are properly installed.

When I try to connect turn on the controller though, the light never turns on for the adapter.

I have already connected my controller to the adapter dongle directly from a win 10 pc and it works as expected.

Hello,

i have an issue with my xbox controller and my headset/mic, when i'm connect on the pc, all is OK :

https://ibb.co/n1tzLf6
https://ibb.co/vs2qVV1

when i connect my controller on shield, i can't choice it :
https://ibb.co/rHJbkxL
https://ibb.co/2kKnjdd
https://ibb.co/qndcZJp

Can you help me please ?

Regards,

Neocide

Hi,

I have a Galaxy s10 with Android 11. However, virtualhere does not show in the settings of the Steam Link app.

I have the VirtuelHere USB Server app installed and not launched.

I read a lot of forum, but found nothing.

I'm beginning to think this is not supported yet with Android 11.

I run a Plex server on my Nvidia Shield, and for some reason the built in "Allow files over local network" option fails after about 10 minutes of moving files to my USB drive.

My wireless Microsoft all-in-one keyboard drops connection if it stays idle for 10 seconds and I must re-enable it again and keep in mind to not leave the keyboard or the mouse idle more than ten seconds.
I just bought VirtualHere and I think this is a major issue.

Can you please advise?

Thank you in advance