Support

Hello,

I found that I can use "-c" to specify a configuration file of VirtualHere. Is there any documentation shows how to use that?
p.s. I want VirtualHere runs as a service and always auto use just my device, without any further operation needed when the Wi-Fi connected to my device.
Your reply will be highly appreciated!

Hi
this is my Logfile:

Oct 8 13:09:10 MyMacBook-Pro vhusbdosx[21994] : enumerateInterfaces: USBInterfaceOpen error kIOReturnExclusiveAccess (exclusive access) at IOService:/IOResources/AppleUSBHostResources/AppleUSBLegacyRoot/AppleUSBXHCI@14000000/Mass Storage@14100000

if I try to Connect with the "Mass Storage" USB Stick it will shortly aviable on the Client, but then lost and back on the Local Machine as "normal" extern drive.

How is it possible to give the exclusiveAccess ?!

When running on a Raspberry Pi 4 B how close is it able to get to 480 bits per sec on the USB port to a Win7 client over a Gigabit ethernet link ???

I want to use it with a USB Oscilloscope which requires this mode.

What are the restrictions imposed on the free version ???

Best regards,
Dave

I upgraded a couple of MacPros (5,1) from 10.9 to 10.13.6
The linux server was upgraded to 4.0.3, the Mac client version now is 4.9.0
I'm serving licence dongles, primarily iLoks. They work for a few minutes before the Virtualhere client crashes, sometimes followed by a kernel panic.
I completely removed and reinstalled the kernel modules with reboots inbetween in order to make sure I have the right version installed.
Do you have any suggestions what to try to find the cause of the problem?
I attached logs that might help.

# kextstat |grep vh

<p>Hello!
</p>
<p>My name is Juliana. We are from Brazil. I work at Luxfacta - IT Solutions.
</p>
<p>We have ordered a license for Virtual Here Server.
</p>
<p>When we start to share our USB camera (Logitech c920) the screen that mirrors the camera in the other pc closes immediately.
</p>
<p>How can this problem be solved?
</p>

Hello, i have a couple of issues this time.
After having the server running for a while, some of the devices reset their names and 4 of them disconnected.
I dont know if anyone touched the setup, but the names should not just reset out of nowhere. I cant recreate the issue as i dont know what happened. Log files didnt really tell me anything.
The 4 that disconnected are all in the same hub, but they show as connected on the server side.

Is there a recommended way to have a CloudHub that is an AP for VirtualHere *and* provides internet access to connected systems via the cloudhub's wifi connection to a router? I'd like to use the WAN when my laptop is connected to Cloudhub.

Woulds any of the "router class" hardware (e.g., GL-MT300N-V2) would handle this better (and easier) than a Raspberry Pi with an extra wifi dongle?

Bonus points if the CloudHub could remember the WLAN wifi SSID/passwords it had previously connected.

Hi!

I try to install virtualhere on my ASUS router with Merlin firmware for remotely using my printer.
It has a readonly file system with only /jffs folder available for writing.

I start virtualhere with "-c /jffs/config.ini" parameter and it seems working.
But when my printer goes to sleep mode and then wakeup I can't see it in the client anymore.
In syslog I can see:
Error 30 creating device node at //_proc_bus_usb_001_007, Read-only file system
Oct 1 07:20:11 [785]: Error making device node at (null)

Hello,

How do I unignore devices?

I have two USB mouse of the same type connected to my host machine, and I want to use virtualhere to send one of them to my client machine. However when I set it to auto use the device, then the next time I start Virtualhere it tries to autouse BOTH devices, and then, because it is the trial version, it tells me I can only use one version. To make it stop trying to use both I tried the ignore function but that made it ignore both devices. And now I cant get them back.

Thanks for any help!

Hi ,