Support

Hello,
I am looking for a small Linux-based computer, capable of running VH. I only need to transfer one USB device over wifi for my Project.
(In my case, an Arduino Pro Micro with an IR Camera attached. Sending x, y coordinates, like a mouse)

With the Pi Zero W2 it works flawlessly with VH, already testest it.

I came across the Onion Omega2+ (very small device) and wondered if there is a more powerful system with a similar small footprint.
After all, the Onion is a few years older than the pi zero w and is based on a 580MHz MIPS CPU.

Hello

Does VirtualHere CloudHub free license  running on rpi 0  w   allow share one device for free as with windows server ? Here https://www.virtualhere.com/hardware we can read:   "These instructions below will install the Free Version of VirtualHere CloudHub on your hardware device. To enable all features of the registered VirtualHere server please purchase a license" but  I'm unable to find page with  differences between free and paid version of CloudHub

Hi i have a Gaming pc in a room and an nvidia shield in another room connected to a monitor which i use for msfs, i ve just buyed a tobii eye tracker 5 to use connected to the shield, virtualhere show the device but when i enable it  doesn t work (say connected, the Red dots blinks but the tracker can t see anything, also the blink should stop after a few second but it does it forever), it works well with others devices (keyboard, yokes etc) and works directly connected to pc, any help please? Thanks 

Good day, we are trying to access HASP keys via the USB ports over a VPN and this is not working. Currently only running a trial version can this be the cause. also do they need specific ports open etc. please advise ASAP. 

Thank you. 

Hi there,

I see on the chart describing the various implementations of VH, there is an option for an embedded client. Does that also run on Rasp Pi? Is there a compiled install for such thing ? I would love to run the server on one Pi and the client on another, so the hardware would be set up once and not require PC software on the client side. Is this possible ? Looking to have the Rasp Pi client usb ports be an extension of the Rasp Pic server usb port plugged into a PC. 

Thank you!

Matthew Wood

I have been trying to connect a raspberry pi to my Laser Engraver ( Neje 3 Max ... not sure this matters but sharing ) I have set up virtualhere USB on raspbian OS 32 bit, I can connect to it with out any issues. When I open up my laser software ( LightBurn ) I can connect to my laser move it all I want, but when I try and do an engraving, it will start, go for about 3 min and then just die. Laser stops, I have been watching the latency spike when trouble shooting, but it seems to be local to the Raspberry Pi, at first I though it was my SD card, replaced it with a HIGH SPEED SD card.

TLDR; What's the best low latency dedicated hardware for Virtual Here server?

Hello, I've been playing around with VH and I really like it. I'm currently running a Pi 3B+ with the general trial build to test things out.

Server  - Ubuntu 22.04.2

VirtualHere server 4.5.8

VirtualHere client 5.5.3

 USB devices are connected to my server, for convenience I renamed them in the client. But at each reboot, the names are set to the original ones. I noticed that every time after a reboot, the address of each device changes in the client, if you look at its properties. The devices are installed in the same USB ports.

How can this be fixed so that the addresses do not change?

I was reading an old post at this link and appears the Android client link is dead. is there a working android client in the works? it looks like it will require root however. what I want to do is connect a virtual server on a Pi to my Dslr so I can send the images instantly to my Android phone while I am out shooting without a wifi router nearby. I am able to do this to Windows 10 computer via a USB connection just fine.

https://www.virtualhere.com/node/104

I am hosting the Mac server on the MacBook Pro M2 apple silicon. The client is on a windows 11 PC. I am trying to use the trial to see if this solution will work my use case, but right now I am not able to get this going. Am I doing something wrong or is this something that will not work with this software?

Thank you,