Support

Hello,

I have three VirtualHere Clients installed. Two in Windows 10, who are working without any issue, and one with Windows 7, where I have an issue.

I have notice that when I install Bonjour and VirtualHere drivers(http://prntscr.com/j4alfh), I can attach and use one key dongle without problem, but if I reboot this system, in the next login session, I will be able to attach it, but it will not work properly. It will not work must of the time, and I have to disattached and attach again, almost everytimes.

Hi,
I have a GL-AR300M running OpenWRT 15.05 and working flawlessly with virtualhere server for MIPS.
My problem is that I can't autostart it on boot, I've followed the FAQ on here https://www.virtualhere.com/oem_faq , downloaded the correct script (vhusbdpin) and changed the line from vhusbdarm to vhusbdmips.
When trying to do start or enable (/etc/init.d/vhusbdpin start or enable) says that /lib/init/vars.sh not found neither /lib/lsb/init-functions

Hello,

My problem is that I have some values (multiple times 0xFF) that are added to the data I receive from VH.
Below an example of what I receive. If I compare it with the direct USB, the multiple "ff" values do not exist in direct USB.

Thanks for the help.

I'm running into a strange problem with a really simple device - A Tripp-Lite Keyspan USB to Serial Adapter with an RS232 loopback adapter attached to it. On a direct USB connection to a PC, I can use PuTTY to open a connection to it, type in data and then get it right back. But on Windows VirtualHere clients (Windows 10, VirtualHere Client 4.4.8), I get nothing but timeout errors. Interestingly, my Debian 9 client (kernel 4.9.0, VirtualHere Client 4.4.8) works just fine. I ran a direct Ethernet cable from the server and client machines to rule out latency (no change).

Hello,

Sorry if this has been covered but I could't find it in any search.
I did notice that iLok isn't support. Shame.

Any idea when it will be?

NAS USB Server - QNAP
Client - OSX
OSX - 10.10.5
iLok with Pro Tools.

Many thanks,
Abayyey.

Hello!

I recently upgraded my Windows 10 PC to the "Spring Creators Update," which is going to be released soon. I found that after the upgrade, my VH client stopped connecting to the server running on my Nvidia Shield TV.

Under the "USB Hubs" node on the client, I periodically see the message "Connecting to USB hub..." but it never completes.

I tried the client on a different (non-upgraded) Windows 10 PC, and it connects to the server just fine.

Hi,
I briefly owned a TPCast before returning it. I purchased a VH license for OpenTPCast, but I do not use it.
I do open source development writing remapping applications for HID devices, so at times I have a requirement to add support for a device that I do not own.
I am thinking that VH would allow me to potentially test code against a device that is remotely located.

While the windows client is running fine I am in stuck while using the raspberry client.
on raspberry pi1 (jessi)
./vhuitarm7 -e -t list
Segmentation fault
./vhclientarmhf -t list
No response from IPC server

Hi.

I have a number of licences for raspberry pi’s running virtualhere software as a remote usb over ip server. I am finding that they are constantly loosing their licence key and I have to manually re-insert it. Is there anything I can do to stop this?

Thanks

I'm running client 4.4.8 and am connected to a server version 3.5.4.

In the gui, right clicking on the server, and then clicking properties, I get a bunch of server information (which is nice).

Running `/vhclientx86_64 -t "SERVER INFO,usbetht1-deb9-64"` (for example), I get nothing. I tried it from both mac and linux. I was hoping to get the same info as in GUI.

Any thoughts? I tried it with/without port, and using the IP address.